Offer · Materials
Cladding, decking and flooring boards from Scandinavia.
Planed cladding boards 21 × 95 and 21 × 145, Södra tongue-and-groove profiles in bevel and softline, rough-sawn Herrgårdspanel laid overlapping, decking and flooring. Kiln dried, from the same yard as the structural timber. This is how they look on our houses.
Official Södra distributor
From our houses
Boards on the facade: vertical, horizontal, black, natural
Six houses we built with timber on the facade. The same board makes a different house depending on direction, width and finish.
01 · JasłoVertical charred boardsSee the house
02 · GnojnikVertical boards in natural spruce, two modules under standing seamSee the house
03 · KrakówHorizontal lap boards in honeySee the house
04 · RzeszówBlack vertical boards, natural timber in the recessesSee the house
05 · Liptovsky TrnoviecHorizontal boards, pale spruce, flat roofSee the house
06 · LeżajskBoards in their natural colour under a standing-seam roofSee the house
Six boards
Boards for cladding, soffits, decking and floors.
Plain planed for a modern facade, profiled tongue-and-groove for soffits and walls, rough Herrgårdspanel the Scandinavian way, grooved or treated smooth for a deck, and tongue-and-groove for a floor that is a ceiling underneath.
- 01
Planed cladding board
Scandinavian spruce planed on four sides, in two sections. Laid vertically board on board it makes a modern, rhythmic facade; with a gap, a modern open cladding. Finish as you like: a hybrid stain or a film-forming preservative in the colour of your choice.
Where
- Vertical board-on-board facade
- Open-joint facade
- Gables and parts of walls
- Fences and carports
- Thickness × width
- 21 × 95
- 21 × 145
- Joint
- square edge, board on board or open joint
- Face
- planed, smooth
- Price
- from PLN 65 per m²
- 02
Södra profiled board, tongue and groove
Thin, light and tight: the tongue sits in the groove, so the wall is closed. The faza variant has a clear V between the boards, softline a soft rounding and a fine gap between the boards. The usual choice for soffits and interiors.
Where
- Roof soffits
- Horizontal and vertical cladding
- Interior walls and ceilings
- Saunas and garden houses
- Thickness × width
- 14 × 121
- 19 × 146
- Joint
- tongue and groove
- Face
- planed, smooth
- Variants
- bevel, softline
- Price
- from PLN 47 per m²
- 03
Herrgårdspanel Södra, rough cladding board
The Swedish manor profile, overlapping: the rough side out holds paint and stain twice as long as a smooth one, and the overlap sheds water without sealing. No relief cuts, so the board stays straight.
Where
- Scandinavian-style horizontal cladding
- Houses, garden houses, saunas
- Farm buildings
- Cladding for opaque paint
- Thickness × width
- 22 × 146
- Joint
- overlapping
- Face
- rough outside, smooth inside
- Price
- from PLN 67 per m²
- 04
Grooved decking board
28 mm Scandinavian spruce with a grooved face that does not slip when wet and drains water. On deck pedestals and stainless screws, oiled once a year, it lasts for years.
Where
- Decks and platforms
- Balconies
- Paths and jetties
- Outdoor steps
- Thickness × width
- 28 × 146
- Joint
- square edge, board on board or open joint
- Face
- grooved, anti-slip
- Price
- from PLN 90 per m²
- 05
Treated decking board, smooth
Spruce 28 × 120, pressure-treated (NTR, green), without grooves: a smooth surface that is easy to clean and oil. The treatment protects the wood inside, the oil keeps the colour on top.
Where
- Decks and platforms
- Balconies
- Jetties and paths
- Outdoor stairs
- Thickness × width
- 28 × 120
- Joint
- square edge, board on board or open joint
- Face
- planed, smooth
- Treatment
- pressure-treated NTR, green
- Price
- from PLN 10.55 per running metre
- 06
Flooring board, tongue and groove
28 mm tongue and groove, finished on both faces: on the floor joists it is the floor, and from below a finished ceiling with the timber showing. One board instead of three layers.
Where
- Floors on joists
- Floors with an exposed ceiling
- Mezzanines and lofts
- Summer houses
- Thickness × width
- 28 × 146
- Joint
- tongue and groove
- Face
- planed, smooth
- Price
- from PLN 90 per m²
Eaves board: planed 28 × 146
Closes the eaves between the roof and the gutter. The same planed Scandinavian spruce board, sold by the cubic metre.
"From" prices are the shop's gross prices per m² as of September 2026; stock changes daily, an adviser confirms quantities and lengths.
Installation
A ventilated facade in four steps
A board on a facade lasts for decades on one condition: it has to dry from both sides. This is how we lay it on our houses.
- 01
Breather membrane on the sheathing
A vapour-open membrane goes onto the wall board: Eurovent Wall Protect or STEICOmulti UDB, joints taped. It stops the wind and any rain that gets through the gaps between boards, and lets vapour from inside out.
- 02
A 38 × 63 batten grid and the gap
We make the grid from 38 × 63 battens: just under 40 mm of ventilation gap, open at the bottom and under the eaves, with an insect mesh. Vertical boards get a second grid: horizontal battens on vertical ones.
- 03
Boards, 30 cm above the ground
A2 stainless screws or ring-shank nails, two per board width. The bottom edge at least 30 cm above ground so splashing rain does not wet it. Board on board with about 25 mm overlap, open joint with a 10 to 20 mm gap.
- 04
Protecting the board
Spruce on a facade always gets protection, in one of two ways. GrandProtekt hybrid stain gives colour and shields against sun and water while the wood underneath still breathes. Impra film-forming preservative lays a thin, elastic film on the board without much change to the grain. Decking gets oil. We paint the board ends and every cut before fitting, because that is where wood takes in most water.
In numbers
Thin for the soffit, thick for the deck
- 6kinds of board in stock, all Scandinavian spruce
- 14millimetres for the thinnest board, the profiled soffit one
- 47zloty per square metre from: 14 × 121 profiled board
- 38millimetres of ventilation gap behind a cladding board
| Where | Board | Laid | Finish |
|---|---|---|---|
| Modern facade | planed 21 × 145, 21 × 95 or profiled 19 × 146 | vertical, board on board or with a gap | as you like: hybrid stain or film-forming preservative |
| Scandinavian facade | Herrgårdspanel 22 × 146 | horizontal, overlapping | opaque paint, stain |
| Soffit, ceiling, interior wall | profiled 14 × 121 or 19 × 146 | tongue and groove, faza or softline | stain, oil or none |
| Deck, balcony, platform | grooved decking 28 × 146 or treated smooth 28 × 120 | on pedestals, stainless screws | oil every season |
| Floor with a visible ceiling | flooring 28 × 146 | tongue and groove on joists | oil or lacquer |
With the boards
Finish and fixings from the same yard
Stains, oils, screws and pedestals, membranes and counter battens: everything from the sheathing to the last coat of colour, on one truck.
Quote
Work it out yourself, in a minute, in the shop
The shop calculator prices boards by the square metre: enter the area of the facade, deck or floor and see an indicative price straight away. One click sends the list to an adviser, who adds an allowance for cuts, picks lengths and gives you a price with delivery.
- 01Pick the board and enter the square metres
- 02See an indicative price straight away
- 03Send the list to an advisor: a quick quote and reply
Contact
Talk boards
Boards and timber are sold by our advisors in Góra Motyczna, Jasło and Gorlice. Call or write with the area of your facade and they will get back to you with quantities, lengths and a price. We help after the sale too: with questions about fitting, come back to a branch or call.
Let's talk
Your facade could be next.
Design, structure and materials from one company. Call or write. An advisor will tell you where to start.